Manuscript Title (16 Bold)

First Writer¹, Second Writer², Willy C ^{3, *} (12 Font Size)

^1,2Department, affiliation, Country (10 Font Size, Italic),

³Mechanical Engineering, Oxford University, USA (10 Font Size, Italic)

Abstract:  (10Font size, Bold) Objective: the abstract body be supposed to review the content of the manuscript. Aim to remain the abstract below 220 text words. Do not make references, abbreviated words, and equations in the abstract. The journal will be published from the same sized copy submitted by you. Method: the title be supposed to appear on a separate page which be supposed to then follow by the writer's name and the institution name and address by indicating suitable superscripts. Title page be supposed to contain the title of the manuscript in bold face, title case (16 font size, uppercase), the names of the writers in normal face (12 font size, lower case, bold) followed by the afilation address in normal face lower case (font size 10). An asterisk (*) should be placed after the corresponding writer's name as superscript whose e-mail id, fax, telephone number can be given at the bottom left corner of the title. Results: corresponding writer has the responsibility to make sure that all co writers are responsive and consent the contents of the manuscript. Conclusion: this will enable us to keep uniformity in the final printed copies of the journal. Please keep in mind that the manuscript you arrange will be photographed and printed as it is received. Keywords writer(s) should give about 5 key words which can identify the most important subjects covered by the manuscript. They should be placed at the end of the abstract. (10 font size, italic)

Keywords: (10 Font Size, Bold): Keyword1; keyword2; about five key words in alphabetical order; separated by semioclon (10Font Size, Italic)

Citation: First writer, Second writer & third writer, ( 2015). Effect of Graphene Filler Content on Mechanical Strength and Hardness for Goat Hair Fibre Reinforced Epoxy Composites. International Journal of Xxxxxxxxxx, X(X), XXX-XXX. doi:10.4273/PENCIS.7.4.10

*Correspondence: Dr. Willy Chou, Department of Recreation and Health-Care Management and Institute of Recreation Industry Management, Chia Nan University of Pharmacy, Tainan, Taiwan. Tel: 886-6-2812811, email: ufan0101@ms22.hinet.net

 Received: XX August 20XX Revised: XX September 20XX, Accepted: XX October 20XX

Open access policy: This open-access article is distributed under the terms of the Creative Commons Attribution Non-Commercial License (creativecommons.org), which permits reuse, distribution and reproduction of the article, provided that the original work is properly cited and the reuse is restricted to noncommercial purposes. For commercial reuse, contact reprints@pencis.com

Introduction (10 Font size, bold)

The introduction of the manuscript is supposed to explain the nature of the problem, previous work, purpose, and the contribution of the manuscript. The contents of each section may be provided to understand easily about the manuscript. The reference should be provided in square bracket, e.g., [2] for all references (10 Font size)

Headings (10 Font size, bold)

Subtitle (10 Font size Bold, Italic)

Headings (10 Font size Font size, Italic)

The headings and sub-headings, first with "1. Introduction", appear in proper case letters and be supposed to be set in bold and aligned flush left. All headings from the Introduction to Acknowledgements are numbered sequentially using 1, 2, 3, etc. Subheadings is numbered 1.1, 1.2, etc. If a subsection should be further divided, the numbers 1.1.1, 1.1.2, etc. The font size for heading is 10 points capital letter and bold face and subsections with 10 points and bold. Do not underline any of the headings, or add dashes, colons, etc. (10 Font size)

Indentations and Equations

The first paragraph under each heading or subheading be supposed to be flush left, and subsequent paragraphs be supposed to have a No-space indentation. A colon is inserted before an equation is accessible, but there is no punctuation subsequent the equation. All equations are numbered and referred to in the text exclusively by a number enclosed in a in a circle bracket (i.e., (2)). Ensure that any miscellaneous numbering system you use in your manuscript cannot be confused with a reference [5] or an equation (2) designation. (10 Font size)

Figures and Tables

To ensure a high quality product, diagrams and lettering should be either computer drafted or drawn using India ink. Figure captions appear below the figure, are flush left, and are in lower case letters. When referring to a figure in the body of the text, the abbreviation "Fig." is used. Figures are supposed to be numbered in the order they appear in the text. Table captions appear centered above the table in upper and lower case letters. When referring to a table in the text, no abbreviation is used and "Table" is capitalized. (10 Font size)

Conclusion

A conclusion section should be included and be supposed to indicate clearly the advantages, limitations, and possible applications of the manuscript. Although a conclusion may review the main points of the manuscript, do not replicate the abstract as the conclusion. A conclusion might elaborate on the importance of the work or suggest applications and extensions. (10 Font size)

Acknowledgements (10 font size, bold)

An acknowledgement section may be presented after the conclusion, if desired. (10 Font size)

References (10 font size, bold) (must be APA format)

 This heading is not assigned a number. A reference list should be 10 Font sizes, included using the following information as a guide. Only cited text references are included. Each reference is referred to in the text by a number with this in a square bracket (i.e., [4]). References should be numbered and ordered according to where they are first mentioned in the manuscript, not alphabetical arrangement.

 

1. Regupathi, R., Rajalakshmi, M., & Dhivya, E. (2014). Experimental Study on Behavior of Reinforced Concrete Beams with Precast SIFCON Laminates. PENCIS International Journal of Engineering, 1(2), 132-139.
2. Book, A. P. P. (1964). The theory of space, time and gravitation.
3. Zines, L., Davies, P. M., & Ricketson, S. Chapters in Books. Recent Developments in the Judicial Interpretation of the Australian, 180, 250.
4. Abercrombie, N., Hill, S., & Turner, B. S. (1980). The dominant ideology thesis. London: Allen & Unwin.
5. York Manuscripts Conference, & York Centre for Medieval Studies. (1989). Latin and vernacular: studies in late-medieval texts and manuscripts;[proceedings of the 1987 York Manuscripts Conference]. A. J. Minnis (Ed.). Brewer.
6. Stim, R. (2014). Patent, Copyright & Trademark: An Intellectual Property Desk Reference. Nolo. 

Review Article

Organization of the review article is at the author's discretion and must be at a length of 6 pages, including all kinds of text like abstract to references. Abstract and key words are required. Tables, figures, illustrations and references are to be arranged according to research papers.